View LTC485_186340.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

LTC485 Low Power RS485 Interface Transceiver
FEATURES
s s s s
DESCRIPTIO
s s
s
s
s s
s
Low Power: ICC = 300A Typ Designed for RS485 Interface Applications Single 5V supply - 7V to 12V Bus Common-Mode Range Permits 7V Ground Difference Between Devices on the Bus Thermal Shutdown Protection Power-Up/Down Glitch-Free Driver Outputs Permit Live Insertion or Removal of Transceiver Driver Maintains High Impedance in Three-State or with the Power Off Combined Impedance of a Driver Output and Receiver Allows Up to 32 Transceivers on the Bus 70mV Typical Input Hysteresis 30ns Typical Driver Propagation Delays with 5ns Skew Pin Compatible with the SN75176A, DS75176A and A96176
The LTC485 is a low power differential bus/line transceiver designed for multipoint data transmission standard RS485 applications with extended common-mode range (12V to - 7V). It also meets the requirements of RS422. The CMOS design offers significant power savings over its bipolar counterpart without sacrificing ruggedness against overload of ESD damage. The driver and receiver feature three-state outputs, with the driver outputs maintaining high impedance over the entire common-mode range. Excessive power dissipation caused by bus contention or faults is prevented by a thermal shutdown circuit which forces the driver outputs into a high impedance state. The receiver has a fail-safe feature which guarantees a high output state when the inputs are left open. The LTC485 is fully specified over the commercial and extended industrial temperature range.
APPLICATI
s s
S
Low Power RS485/RS422 Transceiver Level Translator
TYPICAL APPLICATI
RO1 RE1 DE1 DI1 D
R
VCC1 Rt GND1
A
Rt RO2 RE2 DE2 DI2 D GND2
LTC485 * TA01
R
VCC2
B
U
Driver Outputs
LTC485 * TA02
UO
UO
1
LTC485 ABSOLUTE
(Note 1)
AXI U
RATI GS
PACKAGE/ORDER I FOR ATIO
TOP VIEW RO 1 RE 2 DE 3 DI 4 D R 8 7 6 5 VCC B A GND
Supply Voltage ....................................................... 12V Control Input Voltages ................... - 0.5V to VCC + 0.5V Driver Input Voltage ....................... - 0.5V to VCC + 0.5V Driver Output Voltage ........................................... 14V Receiver Input Voltage.......................................... 14V Receiver Output Voltages .............. - 0.5V to VCC + 0.5V Operating Temperature Range LTC485I...................................... - 40C TA 85C LTC485C.......................................... 0C TA 70C LTC485M.................................. - 55C TA 125C Lead Temperature (Soldering, 10 sec)................. 300C
ORDER PART NUMBER LTC485CJ8 LTC485CN8 LTC485CS8 LTC485IN8 LTC485IS8 LTC485MJ8 S8 PART MARKING 485 485I
J8 PACKAGE 8-LEAD CERAMIC DIP
N8 PACKAGE 8-LEAD PLASTIC DIP
S8 PACKAGE 8-LEAD PLASTIC SOIC
TJMAX = 155C, JA = 100C/ W (J) TJMAX = 100C, JA = 130C/ W (N) TJMAX = 100C, JA = 170C/ W (S)
ELECTRICAL CHARACTERISTICS
SYMBOL VOD1 VOD2 VOD PARAMETER Differential Driver Output Voltage (Unloaded) Differential Driver Output Voltage (with Load) Change in Magnitude of Driver DifferentialOutput Voltage for Complementary States Driver Common-Mode Output Voltage Change in Magnitude of Driver Common-Mode Output Voltage for Complementary States Input High Voltage Input Low Voltage Input Current Input Current (A, B) Differential Input Threshold Voltage for Receiver Receiver Input Hysteresis Receiver Output High Voltage Receiver Outpu Low Voltage Three-State (High Impedance) Output Current at Receiver Receiver Input Resistance Supply Current Driver Short-Circuit Current, VOUT = HIGH Driver Short-Circuit Current, VOUT = LOW Receiver Short-Circuit Current
VCC = 5V 5%, unless otherwise noted. (Notes 2 and 3)
MIN
q q q q
CONDITIONS IO = 0 R = 50 (RS422) R = 27 (RS485), Figure 1 R = 27 or R = 50, Figure 1
TYP
MAX 5
UNITS V V V V
2 1.5
5 0.2
VOC VOC
R = 27 or R = 50, Figure 1 R = 27 or R = 50, Figure 1
q q
3 0.2
VIH VIL IIN1 IIN2 VTH VTH VOH VOL IOZR RIN ICC IOSD1 IOSD2 IOSR
DE, DI, RE DE, DI, RE DE, DI, RE DE = 0, VCC = 0V or 5.25V - 7V VCM 12V VCM = 0V IO = - 4mA, VID = 200mV IO = 4mA, VID = - 200mV VCC = Max, 0.4V VO 2.4V - 7V VCM 12V No Load, Pins 2, 3, 4 = 0V or 5V VO = - 7V VO = 10V 0V VO VCC Outputs Enabled Outputs Disabled VIN = 12V VIN = - 7V
q q q q q q q q q q q q q q q q
2 0.8 2 1 - 0.8 - 0.2 70 3.5 0.4 1 12 500 300 35 35 7 100 100 900 500 250 250 85 0.2
2
U
V V V V A mA mA V mV V V A k A A mA mA mA
W
U
U
WW
W
LTC485
SWITCHI G CHARACTERISTICS
SYMBOL tPLH tPHL tSKEW tr, tf tZH tZL tLZ tHZ tPLH tPHL tSKD tZL tZH tLZ tHZ
tPLH - tPHL Differential Receiver Skew
PARAMETER Driver Input to Output Driver Input to Output Driver Output to Output Driver Rise or Fall Time Driver Enable to Output High Driver Enable to Output Low Driver Disable Time from Low Driver Disable Time from High Receiver Input to Output
Receiver Enable to Output Low Receiver Enable to Output High Receiver Disable from Low Receiver Disable from High
The q denotes specifications which apply over the full operating temperature range. Note 1: Absolute maximum ratings are those beyond which the safety of the device cannot be guaranteed. Note 2: All currents into device pins are positive; all currents out ot device pins are negative. All voltages are referenced to device ground unless otherwise specified.
TEST CIRCUITS
A R VOD R B
LTC485 * F01
3V DE A DI B RDIFF CL2 CL1 A RO B RE 15pF
CL
LTC485 * F02
Figure 3. Driver/Receiver Timing Test Circuit
U
VCC = 5V 5%, unless otherwise noted. (Notes 2 and 3)
MIN
q q q q
CONDITIONS RDIFF = 54, CL1 = CL2 = 100pF, (Figures 3 and 5)
TYP 30 30 5 15 40 40 40 40
MAX 50 50 10 25 70 70 70 70 200 200 50 50 50 50
UNITS ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns
10 10 3
CL = 100pF (Figures 4 and 6) S2 Closed CL = 100pF (Figures 4 and 6) S1 Closed CL = 15pF (Figures 4 and 6) S1 Closed CL = 15pF (Figures 4 and 6) S2 Closed RDIFF = 54, CL1 = CL2 = 100pF, (Figures 3 and 7)
q q q q q q q
30 30
90 90 13 20 20 20 20
CRL = 15pF (Figures 2 and 8) S1 Closed CRL = 15pF (Figures 2 and 8) S2 Closed CRL = 15pF (Figures 2 and 8) S1 Closed CRL = 15pF (Figures 2 and 8) S2 Closed
q q q q
Note 3: All typicals are given for VCC = 5V and TA = 25C. Note 4: The LTC485 is guaranteed by design to be functional over a supply voltage range of 5V 10%. Data sheet parameters are guaranteed over the tested supply voltage range of 5V 5%.
TEST POINT RECEIVER OUTPUT
S1
1k VCC
VOC
CRL 15pF
1k
S2
LTC485 * F02
Figure 1. Driver DC Test Load
Figure 2. Receiver Timing Test Load
S1 OUTPUT UNDER TEST 500 S2 VCC
LTC485 * F03
Figure 4. Driver Timing Test Load #2
3
LTC485
SWITCHI G TI E WAVEFOR S
3V DI 0V t PLH B VO A 1/2 VO VO 0V -VO 10% tr tSKEW 80% 90% VDIFF = V(A) - V(B) tf 20%
LTC485 * F05
1.5V
Figure 5. Driver Propagation Delays
3V DI 0V 5V A, B VOL VOH A, B 0V t ZH t HZ
LTC485 * F06
1.5V t ZL 2.3V
2.3V
Figure 6. Driver Enable and Disable Times
VOH R VOL t PHL VOD2 A, B -VOD2 0V 1.5V OUTPUT f = 1MHz, t r 10ns, t f 10ns INPUT t PLH 1.5V
Figure 7. Receiver Propagation Delays
3V RE 0V 5V R t ZL 1.5V OUTPUT NORMALLY LOW t LZ 0.5V 1.5V f = 1MHz, t r 10ns, t f 10ns 1.5V
R 0V t ZH
Figure 8. Receiver Enable and Disable Times
4
W
1.5V
W
U
f = 1MHz, t r 10ns, t f 10ns t PLH
1.5V 1/2 VO
t SKEW
f = 1MHz, t r 10ns, t f 10ns t LZ OUTPUT NORMALLY LOW
1.5V
0.5V
OUTPUT NORMALLY HIGH
0.5V
LTC485 * F07
OUTPUT NORMALLY HIGH t HZ
0.5V
LTC485 * F08
LTC485
FU CTIO TABLES
LTC485 Transmitting
INPUTS RE X X X X DE 1 1 0 1 DI 1 0 X X LINE CONDITION No Fault No Fault X Fault OUTPUTS B 0 1 Z Z A 1 0 Z Z
PI FU CTIO S
PIN #
1
NAME
RO
DESCRIPTION
Receiver Output. If the receiver output is enabled (RE low), then if A > B by 200mV, RO will be high. If A < B by 200mV, then RO will be low. Receiver Output Enable. A low enables the receiver output, RO. A high input forces the receiver output into a high impedance state. Driver Outputs Enable. A high on DE enables the driver output. A and B, and the chip will function as a line driver. A low input will force the driver outputs into a high impedance state and the chip will function as a line receiver. Driver Input. If the driver outputs are enabled (DE high), then a low on DI forces the outputs A low and B high. A high on DI with the driver outputs enabled will force A high and B low. Ground Connection. Driver Output/Receiver Input. Driver Output/Receiver Input. Positive Supply; 4.75 < VCC < 5.25
2
RE
3
DE
LTC485 Receiving
INPUTS RE 0 0 0 1 DE 0 0 0 0 A-B 0.2V - 0.2V Inputs Open X OUTPUTS R 1 0 1 Z 5 6 7 8 GND A B VCC 4 DI
TYPICAL PERFOR A CE CHARACTERISTICS
Receiver Output Low Voltage vs Output Current
36 32 TA = 25C -18 -16 TA = 25C
Receiver Output High Voltage vs Output Current
4.8 4.6 4.4
OUTPUT CURRENT (mA)
OUTPUT CURRENT (mA)
28 24 20 16 12 8 4 0 0 0.5 1.5 1.0 OUTPUT VOLTAGE (V) 2.0
LTC485 * TPC01
-14 -12 -10 -8 -6 -4 -2 0 5 4 3 OUTPUT VOLTAGE (V) 2
LTC485 * TPC02
OUTPUT VOLTAGE (V)
U
U
U
UW
U
U
Receiver Output High Voltage vs Temperature
I = 8mA
4.2 4.0 3.8 3.6 3.4 3.2 3.0 -50 -25 25 50 0 75 TEMPERATURE (C) 100 125
LTC485 * TPC03
5
LTC485
TYPICAL PERFOR A CE CHARACTERISTICS
Receiver Output Low Voltage vs Temperature
0.9 0.8 0.7 I = 8mA 72 64 TA = 25C
0.6 0.5 0.4 0.3 0.2 0.1 0 -50 -25 25 50 0 75 TEMPERATURE (C) 100 125
OUTPUT CURRENT (mA)
56 48 40 32 24 16 8 0 0 1 3 2 OUTPUT VOLTAGE (V) 4
LTC485 * TPC05
DIFFERENTIAL VOLTAGE (V)
OUTPUT VOLTAGE (V)
LTC485 * TPC03
Driver Output Low Voltage vs Output Current
90 80 TA = 25C -108 -96
INPUT THRESHOLD VOLTAGE (V)
OUTPUT CURRENT (mA)
OUTPUT CURRENT (mA)
70 60 50 40 30 20 10 0 0 1 3 2 OUTPUT VOLTAGE (V) 4
LTC485 * TPC07
Receiver tPLH - tPHL vs Temperature
7.5 7.0 6.5 6.0 5.4 4.8
SUPPLY CURRENT (A)
TIME (ns)
5.5 5.0 4.5 4.0 3.5 3.0 -50 -25 25 50 0 75 TEMPERATURE (C) 100 125
TIME (ns)
LTC485 * TPC10
6
UW
Driver Differential Output Voltage vs Output Current
2.4 2.3 2.2 2.1 2.0 1.9 1.8 1.7 1.6
Driver Differential Output Voltage vs Temperature
RI = 54
1.5 -50
-25
25 50 0 75 TEMPERATURE (C)
100
125
LTC485 * TPC06
Driver Output High Voltage vs Output Current
1.64 TA = 25C 1.63 1.62 1.61 1.60 1.59 1.58 1.57 1.56 0 1 3 2 OUTPUT VOLTAGE (V) 4
LTC485 * TPC08
TTL Input Threshold vs Temperature
-84 -72 -60 -48 -36 -24 -12 0
1.55 -50
-25
25 50 0 75 TEMPERATURE (C)
100
125
LTC485 * TPC09
Driver Skew vs Temperature
640 580 520 460 400 340
Supply Current vs Temperature
4.2 3.6 3.0 2.4 1.8 1.2 0.6 0 -50 -25 25 50 0 75 TEMPERATURE (C) 100 125
DRIVER ENABLED
DRIVER DISABLED 280 220 160 100 -50 -25 25 50 0 75 TEMPERATURE (C) 100 125
LTC485 * TPC11
LTC485 * TPC12
LTC485
APPLICATIO S I FOR ATIO
Basic Theory of Operation
Previous RS485 transceivers have been designed using bipolar technology because the common-mode range of the device must extend beyond the supplies and the device must be immune to ESD damage and latchup. Unfortunately, the bipolar devices draw a large amount of supply current, which is unacceptable for the numerous applications that require low power consumption. The LTC485 is the first CMOS RS485/RS422 transceiver which features ultra-low power consumption without sacrificing ESD and latchup immunity. The LTC485 uses a proprietary driver output stage, which allows a common-mode range that extends beyond the power supplies while virtually eliminating latchup and providing excellent ESD protection. Figure 9 shows the LTC485 output stage while Figure 10 shows a conventional CMOS output stage. When the conventional CMOS output stage of Figure 10 enters a high impedance state, both the P-channel (P1) and the N-channel (N1) are turned off. If the output is then driven above VCC or below ground, the P + /N-well diode
VCC SD3 P1
D1
OUTPUT LOGIC SD4
N1
D2
LTC485 * F09
Figure 9. LTC485 Output Stage
U
(D1) or the N + /P-substrate diode (D2) respectively will turn on and clamp the output to the supply. Thus, the output stage is no longer in a high impedance state and is not able to meet the RS485 common-mode range requirement. In addition, the large amount of current flowing through either diode will induce the well known CMOS latchup condition, which could destroy the device. The LTC485 output stage of Figure 9 eliminates these problems by adding two Schottky diodes, SD3 and SD4. The Schottky diodes are fabricated by a proprietary modification to the standard N-well CMOS process. When the output stage is operating normally, the Schottky diodes are forward biased and have a small voltage drop across them. When the output is in the high impedance state and is driven above VCC or below ground, the parasitic diodes D1 or D2 still turn on, but SD3 or SD4 will reverse bias and prevent current from flowing into the N-well or the substrate. Thus, the high impedance state is maintained even with the output voltage beyond the supplies. With no minority carrier current flowing into the N-well or substrate, latchup is virtually eliminated under power-up or power-down conditions.
VCC P1 D1 LOGIC OUTPUT N1 D2
LTC485 * F10
W
UU
Figure 10. Conventional CMOS Output Stage
7
LTC485
APPLICATIO S I FOR ATIO
The LTC485 output stage will maintain a high impedance state until the breakdown of the N-channel or P-channel is reached when going positive or negative respectively. The output will be clamped to either VCC or ground by a Zener voltage plus a Schottky diode drop, but this voltage is way beyond the RS485 operating range. This clamp protects the MOS gates from ESD voltages well over 2000V. Because the ESD injected current in the N-well or substrate consists of majority carriers, latchup is prevented by careful layout techniques.
A DRIVER OUTPUTS B RECEIVER OUTPUT RO RECEIVER OUTPUT DRIVER OUTPUTS
LTC485 * F11
Figure 11. Receiver tPHL
TTL IN t r, t f < 6ns
D
Figure 13. Receiver Propagation Delay Test Circuit
8
U
Propagation Delay Many digital encoding schemes are dependent upon the difference in the propagation delay times of the driver and the receiver. Using the test circuit of Figure 13, Figures 11 and 12 show the typical LTC485 receiver propagation delay. The receiver delay times are:
tPLH - tPHL = 9ns Typ, VCC = 5V
W
U
U
The driver skew times are: Skew = 5ns Typ, VCC = 5V 10ns Max, VCC = 5V, TA = - 40C to 85C
A
B RO
LTC485 * F12
Figure 12. Receiver tPLH
100pF R 100
BR R
RECEIVER OUT
LTC485 * F13
100pF
LTC485
APPLICATIO S I FOR ATIO
LTC485 Line Length vs Data Rate
The maximum line length allowable for the RS422/RS485 standard is 4000 feet.
100 A LTC485 B TTL IN NOISE GENERATOR C D 4000 FT 26AWG TWISTED PAIR LTC485 TTL OUT
Figure 14. Line Length Test Circuit Figure 17. System Common-Mode Voltage at 110kHz
Using the test circuit in Figure 14, Figures 15 and 16 show that with ~ 20VP-P common-mode noise injected on the line, The LTC485 is able to reconstruct the data stream at the end of 4000 feet of twisted pair wire.
RO DI
COMMON-MODE VOLTAGE (A + B)/2
DI
LTC485 * F15
Figure 15. System Common-Mode Voltage at 19.2kHz
CABLE LENGTH (FT)
RO
DIFFERENTIAL VOLTAGE A - B
DI
LTC485 * F16
Figure 16. System Differential Voltage at 19.2kHz
U
Figures 17 and 18 show that the LTC485 is able to comfortably drive 4000 feet of wire at 110kHz.
RO COMMON-MODE VOLTAGE (A + B)/2 DI
LTC485 * F17
W
UU
RO
COMMON-MODE VOLTAGE (A - B)
LTC485 * F18
Figure 18. System Differential Voltage at 110kHz
When specifying line length vs maximum data rate the curve in Figure 19 should be used:
10k
1k
100
10 10k
100k 1M 2.5M MAXIMUM DATA RATE
10M
LTC485 * F19
Figure 19. Cable Length vs Maximum Data Rate
9
LTC485
TYPICAL APPLICATIO S
Typical RS485 Network
Rt Rt
PACKAGE DESCRIPTIO
CORNER LEADS OPTION (4 PLCS)
0.023 - 0.045 (0.584 - 1.143) HALF LEAD OPTION 0.045 - 0.068 (1.143 - 1.727) FULL LEAD OPTION
NOTE: LEAD DIMENSIONS APPLY TO SOLDER DIP OR TIN PLATE LEADS.
10
U
U
LTC485 * TA03
Dimensions in inches (millimeters) unless otherwise noted. J8 Package 8-Lead Ceramic DIP
0.405 (10.287) MAX 8 7 6 5
0.005 (0.127) MIN
0.025 (0.635) RAD TYP 1 2 3
0.220 - 0.310 (5.588 - 7.874)
4 0.200 (5.080) MAX 0.015 - 0.060 (0.381 - 1.524)
0.290 - 0.320 (7.366 - 8.128)
0.008 - 0.018 (0.203 - 0.457) 0.385 0.025 (9.779 0.635)
0 - 15
0.045 - 0.068 (1.143 - 1.727) 0.014 - 0.026 (0.360 - 0.660)
0.125 3.175 0.100 0.010 MIN (2.540 0.254)
J8 0293
LTC485
PACKAGE DESCRIPTIO U
Dimensions in inches (millimeters) unless otherwise noted. N8 Package 8-Lead Plastic DIP
0.400 (10.160) MAX 8 7 6 5
0.250 0.010 (6.350 0.254)
1
2
3
4
0.300 - 0.320 (7.620 - 8.128)
0.045 - 0.065 (1.143 - 1.651)
0.130 0.005 (3.302 0.127)
0.009 - 0.015 (0.229 - 0.381)
0.065 (1.651) TYP 0.125 (3.175) MIN 0.020 (0.508) MIN
(
+0.025 0.325 -0.015 8.255 +0.635 -0.381
)
0.045 0.015 (1.143 0.381) 0.100 0.010 (2.540 0.254)
0.018 0.003 (0.457 0.076)
N8 0392
S8 Package 8-Lead Plastic SOIC
0.189 - 0.197 (4.801 - 5.004) 8 7 6 5
0.228 - 0.244 (5.791 - 6.197)
0.150 - 0.157 (3.810 - 3.988)
1 0.010 - 0.020 x 45 (0.254 - 0.508) 0.008 - 0.010 (0.203 - 0.254) 0.016 - 0.050 0.406 - 1.270 0- 8 TYP
2
3
4
0.053 - 0.069 (1.346 - 1.752) 0.004 - 0.010 (0.101 - 0.254)
0.014 - 0.019 (0.355 - 0.483)
0.050 (1.270) BSC
SO8 0392
Information furnished by Linear Technology Corporation is believed to be accurate and reliable. However, no responsibility is assumed for its use. Linear Technology Corporation makes no representation that the interconnection of its circuits as described herein will not infringe on existing patent rights.
11
LTC485
U.S. Area Sales Offices
NORTHEAST REGION Linear Technology Corporation One Oxford Valley 2300 E. Lincoln Hwy.,Suite 306 Langhorne, PA 19047 Phone: (215) 757-8578 FAX: (215) 757-5631 SOUTHEAST REGION Linear Technology Corporation 17060 Dallas Parkway Suite 208 Dallas, TX 75248 Phone: (214) 733-3071 FAX: (214) 380-5138 CENTRAL REGION Linear Technology Corporation Chesapeake Square 229 Mitchell Court, Suite A-25 Addison, IL 60101 Phone: (708) 620-6910 FAX: (708) 620-6977 SOUTHWEST REGION Linear Technology Corporation 22141 Ventura Blvd. Suite 206 Woodland Hills, CA 91364 Phone: (818) 703-0835 FAX: (818) 703-0517 NORTHWEST REGION Linear Technology Corporation 782 Sycamore Dr. Milpitas, CA 95035 Phone: (408) 428-2050 FAX: (408) 432-6331
Linear Technology Corporation 266 Lowell St., Suite B-8 Wilmington, MA 01887 Phone: (508) 658-3881 FAX: (508) 658-2701
International Sales Offices
FRANCE Linear Technology S.A.R.L. Immeuble "Le Quartz" 58 Chemin de la Justice 92290 Chatenay Malabry France Phone: 33-1-41079555 FAX: 33-1-46314613 GERMANY Linear Techonolgy GMBH Untere Hauptstr. 9 D-85386 Eching Germany Phone: 49-89-3197410 FAX: 49-89-3194821 JAPAN Linear Technology KK 5F YZ Bldg. Iidabashi, Chiyoda-Ku Tokyo, 102 Japan Phone: 81-3-3237-7891 FAX: 81-3-3237-8010 KOREA Linear Technology Korea Branch Namsong Building, #505 Itaewon-Dong 260-199 Yongsan-Ku, Seoul Korea Phone: 82-2-792-1617 FAX: 82-2-792-1619 SINGAPORE Linear Technology Pte. Ltd. 101 Boon Keng Road #02-15 Kallang Ind. Estates Singapore 1233 Phone: 65-293-5322 FAX: 65-292-0398 TAIWAN Linear Technology Corporation Rm. 801, No. 46, Sec. 2 Chung Shan N. Rd. Taipei, Taiwan, R.O.C. Phone: 886-2-521-7575 FAX: 886-2-562-2285 UNITED KINGDOM Linear Technology (UK) Ltd. The Coliseum, Riverside Way Camberley, Surrey GU15 3YL United Kingdom Phone: 44-276-677676 FAX: 44-276-64851
World Headquarters
Linear Technology Corporation 1630 McCarthy Blvd. Milpitas, CA 95035-7487 Phone: (408) 432-1900 FAX: (408) 434-0507
06/24/93
12
Linear Technology Corporation
1630 McCarthy Blvd., Milpitas, CA 95035-7487
(408) 432-1900 q FAX: (408) 434-0507 q TELEX: 499-3977
LT/GP 0294 5K REV E * PRINTED IN THE USA
(c) LINEAR TECHNOLOGY CORPORATION 1994

▲Up To Search▲

Price & Availability of LTC485

	To Download LTC485 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .